- PPF for Trunk Protection
- Slip Bottle
- Tack Bottle
- Squeegee
- Install Guide
トランクを使って荷物や自転車、ベビーカーなどを運ぶことが多いオーナーに最適です。
ほとんどのお客様はこのキットを自分で取り付けます。 PPF インストールに関するある程度の経験は役に立ちますが、必須ではありません。
取り付け時間: 0.5 時間
推奨温度: 65°F – 75°F
必要なツール:付属の取り付けボトルに水を加えるだけです。ビデオの作り方:
残念ながら、PPF はセラミックコーティングには接着しません。すでにセラミックコートを施してある場合は施工をお勧めしません。
少なくとも 24 時間待ってから運転することを強くお勧めします。これにより、PPF が完全に接着する時間が確保され、水や破片が表面の下に入り込むことがなくなります。
PPF は 65 ~ 75 °F の温度で取り付けるのが最適です。寒すぎると硬く感じる場合があります。熱すぎるとさらに伸びてしまいます。
指が小さい場合は、タック溶液を使用してスキージで押し込むのが最も簡単な方法です。それでも続く場合は、スキージをマイクロファイバーで包み、スキージで押し下げます。マイクロファイバーが水を吸収し、粘着性が高くなります。
ニッケルよりも大きい場合は、PPF を持ち上げて、再度押し下げます。ニッケルより小さい場合は、時間内に消散して蒸発するはずです。
安全を確保するために、少なくとも 24 時間、ただし 48 時間待つことをお勧めします。
はい、必要なものはすべてキットに含まれています。追加する必要があるのは、スリップ アンド タック ボトルに水を加えるだけです。
いいえ、当社のキットは簡単に取り付けられるようにカット済みでお届けします。
可能ですが、十分にご注意ください。隅々まで注意が必要です。スプレーガンを直接端付近に向けるとフィルムが剥がれる場合があります。端に直接スプレーしないでください。大丈夫です。
PPF は乾式取り付けであるビニールと比較して湿式取り付けであるため、調整が簡単です。間違いがあった場合は、当社までご連絡ください。有償で交換品をお送りいたします。
私たちの映画は10年間評価されています。
絶対に。車をさらに簡単にきれいに保つことができる、PPF 専用のセラミック コーティングが多数あります。
Designed for DIY-ers |No cutting required. Pre-cut kits with step by step video installation guides.
All Tools Included | Professional-grade tools for a smooth installation
Guaranteed success| Free replacement program. USA support help.
Lasts up to 10 years| High quality protection film from Avery Dennison.
Our PPF kits are precision-cut to fit perfectly, offering a nearly invisible layer of protection that guards against scratches, chips, and road debris. Keep your Tesla looking brand new for years to come.
These kits are designed for a simple DIY installation. With no cutting required, and easy-to-follow video guides, anyone can achieve professional-level results from the comfort of their garage.
Our PPF is built to last up to 10 years, preserving your Tesla’s finish against daily wear and tear. Plus, it's self-healing, so minor scratches disappear with heat. Learn more about PPF >
After using the "Test Kit" provided with the order and doing really well with the mirror, I decided to attack the task! Took me 2 afternoons to do the job, and it came out pretty good, I end up with couple bobbles that went away with couple weeks.
TESBROS installation videos are great. Great product, ppf is cut exactly to size and specs of the vehicle
Very easy to install. Spray the slip solution liberally, in this case, less is not more.
Here are my few notes, which made me take a star off. Since I have a MYLR '23, I do not have sensor hole cut outs. There was no obvious way of knowing if the straight edge of the PPF, or the curved edge of the PPF went towards the rubber seal of the hatch. The answer: the curved side goes towards the seat, the flat edge goes towards the ground/plastic trim.
So once I got everything set properly, I realized the error, and had to peel it off, quickly make more slip solution with some baby shampoo - and reapply it.
The second - it includes two pieces of vinyl as guides to install the film. I applied the vinyl in the right place - and either it's cut in the incorrect size, or the PPF is cut too small. The distance between the PPF and the vinyl guides was about a half inch either side. I would've expected tolerances that were a little closer, to help eyeball center.
Final note - the PPF towards the hatch gasket stops after the first lip of the bumper - it does not extend past that horizontal flat surface, and continue vertically - under the gasket. Not the end of the world - however just be careful, that flat surface gathers water and road grim easily, and a quick swipe with a microfiber will scratch it. It's visible from the back the car - but fortunately it's not an area that is generally looked at - and difficult to see when the hatch is closed.
If I were asked if I would…
Excellent product. Feels durable and easy to apply.
This install was much easier than the Front PPF install on my Model Y. This is needed to protect your paint from all the ins and outs from your back end. It was effortless to add this as a training item before I got into my Front PPF install. I already had prepared the area as I was doing the areas for the Front PPF install plus had slip and tack solutions all prepared. I wish I would have had the rocker kit to install it all together since I had done all the prep work for the car. Realize the best install is one where you can not even see something different.