I couldn’t be more pleased with how the finished product looks. You won’t find a better DIY kit. Since I had no previous experience I watched the videos twice, it still took me several hours to complete, but looks better than I expected. Seal edges well to avoid dirt entering while driving after. I used a larger table and brought an extra light in the garage. I only had my wife help with larger bumper pieces, but it can be done by yourself. The fender and bumper seams were the most challenging part, but if you take your time you won’t see them! I did have a few bubbles when I was done, but all but 1 or 2 went away within a week. The others are easily fixed. My car was only 2 weeks old, but I still did the entire prep routine and that helped. I had to do many pieces a 2nd or 3rd time due to dirt or not being perfect, just spray your slip solution and start over. Tips: spray plenty of slip when peeling film and take your time - larger pieces are a challenger. 2) remember to always push away from Tack areas and squeegee all moisture out. It will take patience, but it’s so worth it, I feel so much more comfortable driving now. Thanks Tesbros for an awesome product (use Facebook page, Ji is awesome!) Picture shows completed mirror and a couple hood bubbles that went away.

9.8/10 installation for a DIY kit. I even did this outside because I have no garage (Very Early morning, non-windy day, 50- 67 degree F outdoor temp), AND all by my self. It came out pretty much perfect.

I have had some experience in vinyl wrapping of my previous car (roof and interior trims). I will say PPF is WAY easier because it is a wet installation so don't be intimidated.

My advice is to watch the Tesbro Video Guides before.

-0.2 points because I do wish the front bumper/fender did not have any seams and just came in one PFF piece.. , But at the end of the day this was probably a better idea for noobs since it would be a lot more difficult to install a single sheet, which requires stretching of the PPF material.

Some tips while installing:

1. Make sure you thoroughly squeegee all parts of the film to get out all the air bubbles. Even though I was slow and methodical when squeegeeing, I thought everything came out perfectly, except a small bubble in the front bumper corner areas. There was couple slip solution bubbles which I happen to miss. But it's so small, no one will ever notice except me... :( lol

2. If you get any specs of dust, simply use the slip spray bottle to wash out from underneath the film. I recommend not to wear (polyester shirts) NO cotton shirts or pants during install which could potential shed cotton lint. .

3. Make sure you take your time and "sew" the seams right up against each other. This is probably the main advice I would give.…

I was not sure to buy this kit then I decided to pull the triger and get it. My local ppf shop asked for $600 to install the front bumper only and $1650 for full front. I get this kit for about $680 with sales deal 😍 👌. It save me money, the local shop asked to drop the car for 4 days at thier shop that will add extra uber cost to me like $100.

I watched tesbros YouTube videos like 2-3 times and then when I started installing I was following the steps and YouTube like watch each part for each piece before starting then I start installing one piece at a time, this will help to minimize errors. I spent 4 hours prep my car and 12 -14 hours including watching time to installing it. I wash the car on Friday night and start working on it on full Saturday and Sunday.

Tips:

Get 3 Glallon on distilled water before starting

Get big table or 2 tables sit next to each other

Get Ramp to raise the car ( it will give you better access to the lower bumper)

Get someone to help you, my wife was a great help to me

Get big light and tourch light too

Clean the space well

Challenging

The kit designed to have seam lines I understand why they did it because I can't imagine how to installing it without them as it will require more stretch and professional level. However, butt seam eadges is taking time and effort to make it looks good but not easy.

I found some hair dirt inside the film in some areas which cannot removed. These hair dirt was not mine it was some contaminated…